================================================================================
Block 5 --- INCONT --- Control System Input
================================================================================
.. default-role:: sasinp
.. sasblock:: INCONT 5
**INPUT BLOCK STRUCTURE**
The control system input block structure is identical to the standard
|SAS| input block structure in all but one respect. A new card
format known as a signal card has been introduced. These cards
immediately follow the block identifier card and precede the standard
format data cards. The ordering of the different card types is depicted
as follows:
.. image:: media/ControlSystemInput.png
:width: 4in
:align: center
The format for the block identifier card is described :ref:`above <BlockIdentifierRecord>`. For the
control system input block the block name is "INCONT" and the block
number is 5.
**SIGNAL CARDS**
A signal card contains data fields for the FORTRAN variables ISIG,
JTYPE, J1SIG, J2SIG, F1SIG, F2SIG, F3SIG, F4SIG, and F5SIG, with record
format 4I5,5F10.3. These variables are described in :numref:`table-A2.2-b5.1`.
A signal card is used to define a signal in the user's block diagram.
There are four signal types: measured, demand, block, and control. Each
signal must be assigned a unique signal identification number using the
"ISIG" field. The value of ISIG must be greater than zero and less than
999, or between 1000 and 10000.
.. _table-A2.2-b5.1:
.. list-table:: Signal Card Format
:header-rows: 1
:align: center
* - Column
- Fortran Symbol
- Definition
- Variable Type
* - 1-5
- ISIG
- Serial Number
- Integer
* - 6-10
- JTYPE
- Signal Type
- Integer
* - 11-15
- J1SIG
- Signal Descriptor 1
- Integer
* - 16-20
- J2SIG
- Signal Descriptor 2
- Integer
* - 21-30
- F1SIG
- Constant 1
- Real
* - 31-40
- F2SIG
- Constant 2
- Real
* - 41-50
- F3SIG
- Constant 3
- Real
* - 51-60
- F4SIG
- Constant 4
- Real
* - 61-70
- F5SIG
- Constant 5
- Real
**MEASURED SIGNAL**
A measured signal makes available to the block diagram the present value
of a referenced |SAS| variable. The correspondence between the
variable that is referenced and the signal card data field values is
given in :numref:`table-A2.2-b5.4`. Note that all measured
signals have a JTYPE value in the range of -50 to -89 or -101 to -136, inclusive.
**DEMAND SIGNAL**
A demand signal makes available to the block diagram the product of the
current value of a time dependent function defined by the user through a
demand table and an initial condition value. A demand table is a set of
ordered pair values supplied by the user in the format of :numref:`table-A2.2-b5.3` and described by :ref:`Data Card
Input<DataCardInput>`.
The code obtains the demand signal by linearly interpolating among the
table entries using the current time. The initial value is obtained as
described in :numref:`section-6.4.3`. The correspondence
between the demand table and the signal card data fields is given in
:numref:`table-A2.2-b5.4`. Note that a demand signal has a JTYPE
value of -90.
**BLOCK SIGNAL**
A block signal makes available to the block diagram the value at the
output of a block. The correspondence between the block characteristics
and the signal card data fields is given in :numref:`table-A2.2-b5.4`. Note that all block signals have a JTYPE
value in the range from 1 through 23. A measured, demand, or block
signal can be used as an input to a block by specifying on the block's
signal definition card the signal identification number assigned to the
input signal. The signals input to each block type are combined
according to the mathematical expressions given in :numref:`table-BlockSignals`.
.. _table-BlockSignals:
.. list-table:: Basic Mathematical Blocks.
:header-rows: 1
:align: center
:widths: 1,2,2,3,4
:class: longtable
* - JTYPE
- Block
- Type
- Representation
- Mathematical Expression
* - 1
- summer
- function
- |image23|
- :math:`y = g\left( g_{1}u_{1} + g_{2}u_{2} \right)`
* - 2
- multiplier
- function
- |image24|
- :math:`y = gu_{1}u_{2}`
* - 3
- divider
- function
- |image25|
- :math:`y = g\frac{u_{1}}{u_{2}}`
* - 4
- differentiator
- function
- |image26|
- :math:`y = g\frac{\text{d}}{\text{dt}}u`
* - 5
- integrator
- dynamic
- |image27|
- :math:`y = y_{0} + g\int_{0}^{t}{\text{ud}t'}`
* - 6
- lag compensator
- dynamic
- |image28|
- :math:`y + \tau\frac{\text{d}}{\text{dt}}y = gu`
:math:`y\left( 0 \right) = y_{0}`
* - 7
- lead-lag compensator
- dynamic
- |image29|
- :math:`y + \tau_{1}\frac{\text{d}}{\text{dt}}y = g\left( u + \tau_{2}\frac{\text{d}}{\text{dt}}u \right)`
:math:`y\left( 0 \right) = y_{0}`
* - 8
- function generator
- table
- |image30|
- :math:`y = gf\left( u \right)`
* - 9
- maximum value
- function
- |image31|
- :math:`y = \mathrm{\max}\left( u_{1},u_{2} \right)`
* - 10
- minimum value
- function
- |image32|
- :math:`y = \mathrm{\min}\left( u_{1},u_{2} \right)`
* - 11
- time delay
- function
- |image33|
- :math:`y = y_{0}` :math:`0 \leq t \leq \tau`
:math:`y = u\left( t - \tau \right)` :math:`t \geq \tau`
* - 12
- natural logarithm
- function
- |image34|
- :math:`y = \ln u`
* - 13
- exponential
- function
- |image35|
- :math:`y = u_{1}^{u_{2}}`
* - 14
- velocity limiter
- function
- |image36|
- :math:`y = y_{\mathrm{\text{dn}}}` :math:`gu < y_{\mathrm{\text{dn}}}`
:math:`y = y_{\mathrm{\text{up}}}` :math:`gu > y_{\mathrm{\text{up}}}`
:math:`y = gu` otherwise
:math:`y_{\mathrm{\text{dn}}} = y\left( t - h \right) - hv_{\mathrm{\text{dn}}}`
:math:`y_{\mathrm{\text{up}}} = y\left( t - h \right) + hv_{\mathrm{\text{up}}}`
* - 15
- AND
- logic
- |image37|
- :math:`y = 1` :math:`u_{1} > 0,u_{2} > 0`
:math:`y = 0` otherwise
* - 16
- OR
- logic
- |image38|
- :math:`y = 0` :math:`u_{1} \leq 0,u_{2} \leq 0`
:math:`y = 1` otherwise
* - 17
- NOT
- logic
- |image39|
- :math:`y = 0` :math:`u \leq 0`
:math:`y = 1` :math:`u > 0`
* - 18
- comparator
- logic
- |image40|
- :math:`y = 0` :math:`u_{1} < u_{2}`
:math:`y = 1` :math:`u_{1} \geq u_{2}`
* - 19
- sample and hold
- function
- |image41|
- :math:`y\left( t \right) = u_{2}\left( t \right)` :math:`u_{1}\left( t \right) \leq 0`
:math:`y\left( t \right) = u_{2}\left( t_{0} \right)` :math:`u_{1}\left( t \right) \geq 0`,
:math:`t \geq t_{0}`, where
:math:`u_{1}\left( t' \right) \leq 0`
:math:`t' < t_{0}`
* - 20
- J-K flip flop
- logic
- |image42|
- :math:`y^{n + 1} = Q^{n}` :math:`u_{1} \leq 0,u_{2} \leq 0`
:math:`y^{n + 1} = 0` :math:`u_{1} > 0,u_{2} \leq 0`
:math:`y^{n + 1} = 1` :math:`u_{1} \leq 0,u_{2} > 0`
:math:`y^{n + 1} = {\overline{Q}}^{n}` :math:`u_{1} > 0,u_{2} > 0`
* - 21
- constant
- function
- |image43|
- :math:`y = g`
* - 22
- sine
- function
- |image44|
- :math:`y = g_{1}\sin\left( g_{2}u + g_{3} \right)`
* - 23
- variable lag
compensator
- dynamic
- |varlag|
- :math:`y + \tau(t)\frac{d}{dt}y = gu`
:math:`y\left( 0 \right) = y_{0}`
**CONTROL SIGNALS**
A control signal is used to set the value of a |SAS| variable
equal to the value of a block signal. The correspondence between the
block signal and the |SAS| variable and the signal card data
fields is given in :numref:`table-A2.2-b5.4`. Note that all
control signals have a JTYPE value that ranges from -1 through -10.
**END OF SIGNALS**
A sequence of signal definition cards is delimited by a signal card with
the ISIG field entry equal to "999".
This card also contains flags for the binary output file print interval
and control of the steady-state solution finder. First, the absolute
value of the JTYPE field for the 999 card is sets the print interval for
control system results output to the binary output file CONTROL.dat.
Second, the J1SIG field is used to determine whether the steady-state
solution finder is to be used. An entry of "1" activates the
steady-state solution finder, while any other entry in this field causes
the solution finder to be bypassed. (A discussion of the initial
condition option is given in :numref:`section-6.4.3`.)
Finally, the J2SIG field allows the user to control the amount of
steady-state output generated. An entry of "1" produces an extended
output for trouble shooting purposes, while any other entry produces a
standard output.
The JTYPE field is also used to generate an extended print-out during
the transient for debugging purposes. The debug print is generated by
setting the JTYPE field of the 999 card to a negative value. The
print-out begins at the time specified on the F1SIG field.
**DATA CARDS**
A data card contains the data fields for the FORTRAN variables LOC, N,
VAR1, VAR2, VAR3, VAR4, and VAR5, with the record format (2I6,5E12.5).
The variables are defined in :ref:`Data Card Input<DataCardInput>`.
A data card appearing in the control system block has a format identical
to the standard |SAS| data card used in other input blocks and
is processed in the same way. The format information given above is the
same as in the SAS manuals and is given here for completeness.
Data cards are used to construct demand tables and function generator
tables, and to supply solution control parameters. These quantities and
their storage locations are defined in :ref:`Data Card
Input<DataCardInput>`.
.. _table-A2.2-b5.3:
.. list-table:: Data Card Format
:header-rows: 1
:align: center
:widths: auto
* - Column
- FORTRAN
Symbol
- Definition
- Variable
Type
* - 1
- LOC
- Storage Location of VAR1
- Integer
* - 7
- N
- Number of Consecutive Locations
- Integer
* - 13
- VAR1
- Constant 1
- Real
* - 25
- VAR2
- Constant 2
- Real
* - 37
- VAR3
- Constant 3
- Real
* - 49
- VAR4
- Constant 4
- Real
* - 61
- VAR5
- Constant 5
- Real
|
.. _DataCardInput:
**DATA CARD INPUT**
.. sasinp:: CTLTAB(J,J1SIG)
:location: 1-2000
Table of normalized demand values. A table is defined when at least two entries are provided. Index J1SIG designates the table number and J is the entry number in the table.
Dimension (20,100).
.. sasinp:: CTLTIM(J,J1SIG)
:location: 2001-4000
Times for `CTLTAB` table. Values must be in ascending order.
Dimension (20,100).
.. sasinp:: CTLFNC(J,J1SIG)
:location: 4001-6000
Table of function generator dependent variables. A table is defined when at least two entries are provided. Index J1SIG designates the table number and J is the entry number in the table.
Dimension (20,100).
.. sasinp:: CTLSIG(J,J1SIG)
:location: 6001-8000
Table of independent variables for `CTLFNC` table. Values must be in ascending order.
Dimension (20,100).
.. sasinp:: EPSCS
:location: 8001
Convergence parameter for dynamic blocks over a subinterval. Must be greater than zero.
.. sasinp:: EPSCPL
:location: 8002
Maximum relative change in a control signal over a subinterval. Must be greater than zero.
**SUMMARY OF CONTROL SYSTEM SIGNALS**
.. _table-A2.2-b5.4:
.. list-table:: Signal Card Contents
:header-rows: 1
:align: center
:widths: 1,2,2
* - Signal Type
- Signal Variable
- Card Contents
* - Measured
- Compressible Volume Pressure, PRESL3
- JTYPE = -50
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Segment Flowrate, FLOWSL3
- JTYPE = -51
J1SIG = Liquid Segment Number, ISGL
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Cover Gas Interface Elevation, ZINTR3
- JTYPE = -52
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Mass, XLQMS3
- JTYPE = -53
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Cover Gas Volume, VOLGC3
- JTYPE = -54
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Time
- JTYPE = -55
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Pump Head, HEADP3
- JTYPE = -56
J1SIG = Pump Number, IPMP
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Temperature, TLQCV3
- JTYPE = -57
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Density, DNSCV3
- JTYPE = -58
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Wall Temperature, TWLCV3
- JTYPE = -59
J1SIG = Volume Number, ICV
J2SIG = Thick-walled node ID, optional
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Cover Gas Pressure, PRESG3
- JTYPE = -60
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Cover Gas Mass, GASMS3
- JTYPE = -61
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Cover Gas Temperature, TGASC3
- JTYPE = -62
J1SIG = Volume Number, ICV
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Not Used.
- JTYPE = -63
* - Measured
- Liquid Segment Temperature, TSLIN3
- JTYPE = -64
J1SIG = Segment Number, ISGL
J2SIG = 1 (Inlet)
J2SIG = 2 (Outlet)
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Pump Speed, PSPED3
- JTYPE = -65
J1SIG = Pump Number, IPMP
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Core Channel Coolant Flowrate, CHFLO3
- JTYPE = -66
J1SIG = Channel Number, ICH
J2SIG = 1 (Inlet)
J2SIG = 2 (Outlet)
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Node Temperature, TLNOD3
- JTYPE = -67
J1SIG = Node Number, INOD
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Wall Node Temperature, TWNOD3
- JTYPE = -68
J1SIG = Node Number, INOD
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Liquid Element Temperature, TELEM
- JTYPE = -69
J1SIG = Element Number, IEL
J2SIG = 1 (Inlet)
J2SIG = 2 (Outlet)
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Not Used.
- JTYPE = -70
* - Measured
- Core Channel Outlet Temperature, CHFCOF
- JTYPE = -71
J1SIG = Channel Number, ICH
J2SIG = 1 (Inlet)
J2SIG = 2 (Outlet)
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Normalized Reactor Power, EXP(POWVA(3,1))
- JTYPE = -72
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Normalized Fission Power, POWFS0\*AMPO
- JTYPE = -73
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Normalized Decay Power, Sum(POWWT(I)\*POWDKH(I))
- JTYPE = -74
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Equivalent Circuit EM Pump Voltage
- JTYPE = -75
J1SIG = Pump Number, IPMP
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Equivalent Circuit EM Pump Frequency
- JTYPE = -76
J1SIG = Pump Number, IPMP
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Equivalent Circuit EM Pump Current
- JTYPE = -77
J1SIG = Pump Number, IPMP
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Equivalent Circuit EM Pump Phase Angle
- JTYPE = -78
J1SIG = Pump Number, IPMP
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Not Used.
- JTYPE = -79,...,-82
* - Measured
- Steam Generator Feedwater Mass Inlet Flowrate
- JTYPE = -83
J2SIG = SG Number
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Steam Generator Feedwater Inlet Enthalpy
- JTYPE = -84
J2SIG = SG Number
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Steam Generator Steam Mass Flowrate
- JTYPE = -85
J2SIG = SG Number
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Steam Generator Outlet Temperature
- JTYPE = -86
J2SIG = SG Number
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Steam Generator Steam Pressure
- JTYPE = -87
J2SIG = SG Number
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Steam Generator Water Level
- JTYPE = -88
J2SIG = SG Number
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Steam Generator Steam Outlet Enthalpy
- JTYPE = -89
J2SIG = SG Number
F3SIG = Initial Condition Flag
F4SIG = Y\ :sub:`o`
* - Demand
- Demand Table
- JTYPE = -90
J1SIG = Demand Table Number
J2SIG = Number of Entries in Table
F4SIG = Y\ :sub:`o`
* - Measured
- Fuel Centerline Temperature
- JTYPE = -101
J1SIG = Channel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Fuel Average Temperature
- JTYPE = -102
J1SIG = Channel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Fuel Surface Temperature
- JTYPE = -103
J1SIG = Channel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Clad Inner Wall Temperature
- JTYPE = -104
J1SIG = Channel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Clad Mid Wall Temperature
- JTYPE = -105
J1SIG = Chanel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Clad Outer Wall Temperature
- JTYPE = -106
J1SIG = Channel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Temperature
- JTYPE = -107
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Pressure
- JTYPE = -108
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Saturation Temperature
- JTYPE = -109
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Boiling Margin
- JTYPE = -110
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Average Temperature
- JTYPE = -111
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Structure Inner Temperature
- JTYPE = -112
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Structure Outer Temperature
- JTYPE = -113
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Reflector Inner Temperature
- JTYPE = -114
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Reflector Outer Temperature
- JTYPE = -115
J1SIG = Channel Number
J2SIG = MZC Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Peak Fuel Temperature
- JTYPE = -116
J1SIG = Channel Number
J2SIG = (Optional) If non-zero, peak fuel temperature is provided over all channels in the range J1SIG ≤ ICH ≤ J2SIG
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Peak Clad Temperature
- JTYPE = -117
J1SIG = Channel Number
J2SIG = (Optional) If non-zero, peak cladding temperature is provided over all channels in the range J1SIG ≤ ICH ≤ J2SIG
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Peak Coolant Temperature
- JTYPE = -118
J1SIG = Channel Number
J2SIG = (Optional) If non-zero, peak coolant temperature is provided over all channels in the range J1SIG ≤ ICH ≤ J2SIG
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Minimum Boiling Margin
- JTYPE = -119
J1SIG = Channel Number
J2SIG = (Optional) If non-zero, minimum boiling margin temperature is provided over all channels in the range J1SIG ≤ ICH ≤ J2SIG
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Inlet Temperature
- JTYPE = -120
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Inlet Pressure
- JTYPE = -121
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Inlet Flowrate
- JTYPE = -122
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Outlet Temperature
- JTYPE = -123
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Outlet Pressure
- JTYPE = -124
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Coolant Outlet Flowrate
- JTYPE = -125
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Maximum Coolant Outlet Temperature
- JTYPE = -126
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Minimum Coolant Outlet Temperature
- JTYPE = -127
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Pin Bundle ΔT
- JTYPE = -128
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Pin Bundle ΔP
- JTYPE = -129
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Assembly Bundle ΔT
- JTYPE = -130
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Assembly Bundle ΔP
- JTYPE = -131
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Assembly Power
- JTYPE = -132
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Pin Linear Power
- JTYPE = -133
J1SIG = Channel Number
J2SIG = MZ Mesh Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Peak Pin Linear Power
- JTYPE = -134
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Fission Gas Plenum Temperature
- JTYPE = -135
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Measured
- Fission Gas Plenum Pressure
- JTYPE = -136
J1SIG = Channel Number
F1SIG = Scaling Factor
F2SIG = Offset
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Summer
- JTYPE = 1
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F1SIG = g\ :sub:`1`
F2SIG = g\ :sub:`2`
F3SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Multiplier
- JTYPE = 2
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Divider
- JTYPE = 3
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Differentiator
- JTYPE = 4
J1SIG = Input Signal 1, ISIG
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Integrator
- JTYPE = 5
J1SIG = Input Signal 1, ISIG
F1SIG = g
F3SIG = Initial Condition Flag
F4SIG = Y\ :sub:`0`
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Block
- Lag Compensator
- JTYPE = 6
J1SIG = Input Signal 1, ISIG
F1SIG = g
F2SIG = Tau
F4SIG = Y\ :sub:`0` (Not used when J1SIG(999) = 1)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Block
- Lead - Lag Compensator
- JTYPE = 7
J1SIG = Input Signal 1, ISIG
F1SIG = g
F2SIG = :math:`\mathrm{\tau}`\ :sub:`1`
F3SIG = :math:`\mathrm{\tau}`\ :sub:`2`
F4SIG = Y\ :sub:`0`\ Y\ :sub:`o` (Not used when J1SIG(999) = 1)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Block
- Function Generator
- JTYPE = 8
J1SIG = Input Signal 1, ISIG
J2SIG = Function Generator Table Number
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Maximum
- JTYPE = 9
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Minimum
- JTYPE = 10
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Time Delay
- JTYPE = 11
J1SIG = Input Signal 1, ISIG
F1SIG = :math:`\mathrm{\tau}`
F4SIG = Y\ :sub:`0` (Not used when J1SIG(999) = 1)
* - Block
- Natural Logarithm
- JTYPE = 12
J1SIG = Input Signal 1, ISIG
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Exponentation
- JTYPE = 13
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Velocity Limiter
- JTYPE = 14
J1SIG = Input Signal 1, ISIG
F1SIG = V\ :sub:`down`
F2SIG = V\ :sub:`up`
F3SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- AND
- JTYPE = 15
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- OR
- JTYPE = 16
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- NOT
- JTYPE = 17
J1SIG = Input Signal 1, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Comparator
- JTYPE = 18
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Sample and Hold
- JTYPE = 19
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Y\ :sub:`0` (optional)
* - Block
- JK Flip-Flop
- JTYPE = 20
J1SIG = Input Signal 1, ISIG
J2SIG = Input Signal 2, ISIG
F4SIG = Q\ :sub:`0`
* - Block
- Constant
- JTYPE = 21
F1SIG = g
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Sine Function
- JTYPE = 22
J1SIG = Input Signal 1, ISIG
F1SIG = g1
F2SIG = g2
F3SIG = g3
F4SIG = Y\ :sub:`0` (optional)
* - Block
- Variable Lag Compensator
- JTYPE = 23
J1SIG = Input Signal 1, ISIG (u)
J2SIG = Input Signal 2, ISIG (Tau)
F1SIG = g
F4SIG = Y\ :sub:`0` (Not used when J1SIG(999) = 1)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Reactivity, $
- JTYPE = -1
J1SIG = Signal Number Used
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Normalized Pump Motor Torque
- JTYPE = -2
J1SIG = Signal Number Used
J2SIG = Pump Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Steam Generator Feedwater Mass Flowrate
- JTYPE = -3
J1SIG = Signal Number Used
J2SIG = Steam Generator Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Steam Generator Feedwater Enthalpy
- JTYPE = -4
J1SIG = Signal Number Used
J2SIG = Steam Generator Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Steam Generator Steam Mass Flowrate
- JTYPE = -5
J1SIG = Signal Number Used
J2SIG = Steam Generator Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Sodium Valve Loss Coefficient
- JTYPE = -6
J1SIG = Signal Number Used
J2SIG = Valve Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Steam Generator Steam Pressure
- JTYPE = -7
J1SIG = Signal Number Used
J2SIG = Steam Generator Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- Air Dump Heat Exchanger Air Mass Flowrate
- JTYPE = -8
J1SIG = Signal Number Used
J2SIG = Air Dump Heat Exchanger Number
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
* - Control
- :ref:`Simulation Trip <simulation_trip>`
- JTYPE = -10
J1SIG = Signal Number Used
J2SIG = Latching option (0, Unlatched; 1, Latched)
F4SIG = Y\ :sub:`0` (optional)
F5SIG = E\ :sub:`z` (Zero Crossing Parameter)
.. |image23| image:: media/image23.png
:width: 1.19586in
:height: 0.74194in
.. |image24| image:: media/image24.png
:width: 1.24889in
:height: 0.75000in
.. |image25| image:: media/image25.png
:width: 1.24889in
:height: 0.75000in
.. |image26| image:: media/image26.png
:width: 1.24566in
:height: 0.75000in
.. |image27| image:: media/image27.png
:width: 1.33328in
:height: 0.75000in
.. |image28| image:: media/image28.png
:width: 1.33328in
:height: 0.75000in
.. |image29| image:: media/image29.png
:width: 1.33328in
:height: 0.75000in
.. |image30| image:: media/image30.png
:width: 1.51397in
:height: 0.75000in
.. |image31| image:: media/image31.png
:width: 1.24889in
:height: 0.75000in
.. |image32| image:: media/image32.png
:width: 1.24889in
:height: 0.75000in
.. |image33| image:: media/image33.png
:width: 1.24889in
:height: 0.75000in
.. |image34| image:: media/image34.png
:width: 1.24566in
:height: 0.75000in
.. |image35| image:: media/image35.png
:width: 1.55228in
:height: 0.75000in
.. |image36| image:: media/image36.png
:width: 1.24566in
:height: 0.75000in
.. |image37| image:: media/image37.png
:width: 1.25190in
:height: 0.75000in
.. |image38| image:: media/image38.png
:width: 1.25190in
:height: 0.75000in
.. |image39| image:: media/image39.png
:width: 1.24889in
:height: 0.75000in
.. |image40| image:: media/image40.png
:width: 1.25190in
:height: 0.75000in
.. |image41| image:: media/image41.png
:width: 1.24889in
:height: 0.75000in
.. |image42| image:: media/image42.png
:width: 1.24889in
:height: 0.75000in
.. |image43| image:: media/image43.png
:width: 0.99598in
:height: 0.75000in
.. |image44| image:: media/image44.png
:width: 1.24566in
:height: 0.75000in
.. |varlag| image:: media/VarLag.png
:width: 1.25in